View TSX561AILT_7187816.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

this is information on a product in full production. may 2013 docid023274 rev 3 1/27 27 tsx561, tsx562, tsx564, tsx561a, tsx562a, tsx564a micropower, wide bandwidth (900 khz), 16 v cmos operational amplifiers datasheet - production data features ? low power consumption: 235 a typ. at 5 v ? supply voltage: 3 v to 16 v ? gain bandwidth product: 900 khz typ. ? low offset voltage ? ?a? version: 600 v max. ? standard version: 1 mv max. ? low input bias current: 1 pa typ. ? high tolerance to esd: 4 kv ? wide temperature range: -40 to +125 c ? automotive qualification ? tiny packages available ?sot23-5 ? dfn8 2 mm x 2 mm, miniso8 ? qfn16 3 mm x 3 mm, tssop14 benefits ? power savings in power-conscious applications ? easy interfacing with high impedance sensors related products ? see tsx63x series for reduced power consumption (45 a, 200 khz) ? see tsx92x series for higher gain bandwidth products (10 mhz) applications ? industrial and automotive signal conditioning ? active filtering ? medical instrumentation ? high impedance sensors description the tsx56x, tsx56xa series of operational amplifiers benefits from stmicroelectronics ? 16 v cmos technology to offer state-of-the-art accuracy and performance in the smallest industrial packages. the tsx56x, tsx56xa have pinouts compatible with industry standards and offer an outstanding speed/power consumption ratio, 900 khz gain bandwidth product while consuming only 250 a at 16 v. such features make the tsx56x, tsx56xa ideal for sensor interfaces and industrial signal conditioning. the wide temperature range and high esd tolerance ease use in harsh automotive applications. sot23-5 tssop14 miniso8 dfn8 2x2 qfn16 3x3 single dual quad table 1. device summary version standard v io enhanced v io single tsx561 tsx561a dual tsx562 tsx562a quad tsx564 tsx564a www.st.com
contents tsx56x, tsx56xa 2/27 docid023274 rev 3 contents 1 pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 absolute maximum ratings and operating c onditions . . . . . . . . . . . . . 4 3 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.1 operating voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.2 rail-to-rail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.3 input offset voltage drift over temperature . . . . . . . . . . . . . . . . . . . . . . . . 15 4.4 long term input offset voltage drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.5 pcb layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.6 macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.1 sot23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.2 dfn8 2x2 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.3 miniso8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.4 qfn16 3x3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.5 tssop14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6 ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
docid023274 rev 3 3/27 tsx56x, tsx56xa pin connections 1 pin connections figure 1. pin connections for each package (top view) dfn8 2x2 (tsx562) miniso8 (tsx562) tssop14 (tsx564) qfn16 3x3 (tsx564) single sot23-5 (tsx561) dual quad 9&& 9&& 287 ,1 ,1 287 ,1 ,1 9&& 9&& 287 ,1 ,1 287 ,1 ,1 ,1 9&& 1& ,1 ,1 9&& 1& ,1 ,1 287 287 ,1 ,1 287 287 ,1
absolute maximum ratings and operating conditions tsx56x, tsx56xa 4/27 docid023274 rev 3 2 absolute maximum ratings and operating conditions table 2. absolute maximum ratings (amr) symbol parameter value unit v cc supply voltage (1) 1. all voltage values, except differential voltage , are with respect to network ground terminal. 18 v v id differential input voltage (2) 2. the differential voltage is the non-inverting input term inal with respect to the inverting input terminal. v cc v in input voltage (3) 3. v cc - v in must not exceed 18 v, v in must not exceed 18 v. v cc- - 0.2 to v cc+ + 0.2 i in input current (4) 4. input current must be limited by a resistor in series with the inputs. 10 ma t stg storage temperature -65 to +150 c r thja thermal resistance junction to ambient (5)(6) sot23-5 dfn8 2x2 miniso8 qfn16 3x3 tssop14 5. short-circuits can c ause excessive heating and destructive dissipation. 6. r th are typical values. 250 120 190 80 100 c/w r thjc thermal resistance junction to case dfn8 2x2 qfn16 3x 33 30 t j maximum junction temperature 150 c esd hbm: human body model (7) 7. human body model: 100 pf discharged through a 1.5 k resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 4kv mm: machine model for tsx561 (8) 8. machine model: a 200 pf cap is charged to the spec ified voltage, then discharged directly between two pins of the device with no external se ries resistor (internal resistor < 5 ), done for all couples of pin combinations with other pins floating. 200 v mm: machine model for tsx562 and tsx564 (8) 100 cdm: charged device model (9) 9. charged device model: all pins plus package ar e charged together to the specified voltage and then discharged directly to ground. 1.5 kv latch-up immunity 200 ma table 3. operating conditions symbol parameter value unit v cc supply voltage 3 to 16 v v icm common mode input voltage range v cc- - 0.1 to v cc+ + 0.1 t oper operating free air temperature range -40 to +125 c
docid023274 rev 3 5/27 tsx56x, tsx56xa electrical characteristics 3 electrical characteristics table 4. electrical characteristics at v cc+ = +3.3 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l =10 k connected to v cc /2 (unless otherwise specified) symbol parameter conditions min. typ. max. unit dc performance v io offset voltage tsx56xa, t = 25 c 600 v tsx56xa, -40 c < t < 125 c 1800 tsx56x, t = 25 c 1 mv tsx56x, -40 c < t < 125 c 2.2 v io / t input offset voltage drift -40 c < t < 125 c (1) 212 v/c i io input offset current (v out = v cc /2) t = 25 c 1 100 (2) pa -40 c < t < 125 c 1 200 (2) i ib input bias current (v out = v cc /2) t = 25 c 1 100 (2) -40 c < t < 125 c 1 200 (2) cmr1 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc -1.5 v, v out = v cc /2, r l > 1 m ) t = 25 c 63 80 db -40 c < t < 125 c 59 cmr2 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc +0.1 v, v out = v cc /2, r l > 1 m ) t = 25 c 47 66 -40 c < t < 125 c 45 a vd large signal voltage gain (v out = 0.5 v to (v cc - 0.5 v), r l > 1 m ) t = 25 c 85 -40 c < t < 125 c 83 v oh high level output voltage (v oh = v cc - v out ) t = 25 c 70 mv -40 c < t < 125 c 100 v ol low level output voltage t = 25 c 70 -40 c < t < 125 c 100 i out i sink (v out = v cc ) t = 25 c 4.3 5.3 ma -40 c < t < 125 c 2.5 i source (v out = 0 v) t = 25 c 3.3 4.3 -40 c < t < 125 c 2.5 i cc supply current (per channel, v out = v cc /2, r l > 1 m ) t = 25 c 220 300 a -40 c < t < 125 c 350
electrical characteristics tsx56x, tsx56xa 6/27 docid023274 rev 3 ac performance gbp gain bandwidth product r l = 10 k , c l = 100 pf 600 800 khz f u unity gain frequency 690 m phase margin 55 degree g m gain margin 9 db sr slew rate r l = 10 k , c l = 100 pf, v out = 0.5 v to v cc - 0.5 v 1v/ s e n low-frequency peak-to-peak input noise bandwidth: f = 0.1 to 10 hz 16 v pp e n equivalent input noise voltage density f = 1 khz f = 10 khz 55 29 thd+n total harmonic distortion + noise follower configuration, f in = 1 khz, r l = 100 k , v icm = (v cc -1.5 v)/2, bw = 22 khz, v out = 1 v pp 0.004 % 1. see section 4.3: input offset voltage drift over temperature on page 15 . 2. guaranteed by design. table 4. electrical characteristics at v cc+ = +3.3 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l =10 k connected to v cc /2 (unless otherwise specified) (continued) symbol parameter conditions min. typ. max. unit nv hz ----------- -
docid023274 rev 3 7/27 tsx56x, tsx56xa electrical characteristics table 5. electrical characteristics at v cc+ = +5 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l = 10 k connected to v cc /2 (unless otherwise specified) symbol parameter conditions min. typ. max. unit dc performance v io offset voltage tsx56xa, t = 25 c 600 v tsx56xa, -40 c < t < 125 c 1800 tsx56x, t = 25 c 1 mv tsx56x, -40 c < t < 125 c 2.2 v io / t input offset voltage drift -40 c < t < 125 c (1) 212 v/c v io long-term input offset voltage drift t = 25 c (2) 5 i io input offset current (v out = v cc /2) t = 25 c 1 100 (3) pa -40 c < t < 125 c 1 200 (3) i ib input bias current (v out = v cc /2) t = 25 c 1 100 (3) -40 c < t < 125 c 1 200 (3) cmr1 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc - 1.5 v, v out = v cc /2, r l > 1 m ) t = 25 c 66 84 db -40 c < t < 125 c 63 cmr2 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc + 0.1 v, v out = v cc /2, r l > 1 m ) t = 25 c 50 69 -40 c < t < 125 c 47 a vd large signal voltage gain (v out = 0.5 v to (v cc - 0.5 v), r l > 1 m ) t = 25 c 85 -40 c < t < 125 c 83 v oh high level output voltage (v oh = v cc - v out ) r l = 10 k , t = 25 c r l = 10 k , -40 c < t < 125 c 70 100 mv v ol low level output voltage r l = 10 k , t = 25 c r l = 10 k , -40 c < t < 125 c 70 100 i out i sink v out = v cc , t = 25 c 11 14 ma v out = v cc , -40 c < t < 125 c 8 i source v out = 0 v, t = 25 c 9 12 v out = 0 v, -40 c < t < 125 c 7 i cc supply current (per channel, v out = v cc /2, r l > 1 m ) t = 25 c 235 350 a -40 c < t < 125 c 400 nv month ---------------------------
electrical characteristics tsx56x, tsx56xa 8/27 docid023274 rev 3 ac performance gbp gain bandwidth product r l = 10 k , c l = 100 pf 700 850 khz f u unity gain frequency 730 m phase margin 55 degree g m gain margin 9 db sr slew rate r l = 10 k , c l = 100 pf, v out = 0.5 v to v cc - 0.5 v 1.1 v/ s e n low-frequency peak-to-peak input noise bandwidth: f = 0.1 to 10 hz 15 v pp e n equivalent input noise voltage density f = 1 khz f = 10 khz 55 29 thd+n total harmonic distortion + noise follower configuration, f in = 1 khz, r l = 100 k , v icm = (v cc - 1.5 v)/2, bw = 22 khz, v out = 2 v pp 0.002 % 1. see section 4.3: input offset voltage drift over temperature on page 15 . 2. typical value is based on the v io drift observed after 1000h at 125 c extrapo lated to 25 c using the arrhenius law and assuming an activation energy of 0.7 ev. the operational amplifier is aged in follower mode configuration. 3. guaranteed by design. table 5. electrical characteristics at v cc+ = +5 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l = 10 k connected to v cc /2 (unless otherwise specified) (continued) symbol parameter conditions min. typ. max. unit nv hz ----------- -
docid023274 rev 3 9/27 tsx56x, tsx56xa electrical characteristics table 6. electrical characteristics at v cc+ = +16 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l = 10 k connected to v cc /2 (unless otherwise specified) symbol parameter conditions min. typ. max. unit dc performance v io offset voltage tsx56xa, t = 25 c 600 v tsx56xa, -40 c < t < 125 c 1800 tsx56x, t = 25 c 1 mv tsx56x, -40 c < t < 125 c 2.2 v io / t input offset voltage drift -40 c < t < 125 c (1) 212 v/c v io long-term input offset voltage drift t = 25 c (2) 1.6 i io input offset current (v out = v cc /2) t = 25 c 1 100 (3) pa -40 c < t < 125 c 1 200 (3) i ib input bias current (v out = v cc /2) t = 25 c 1 100 (3) -40 c < t < 125 c 1 200 (3) cmr1 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc - 1.5 v, v out = v cc /2, r l > 1 m ) t = 25 c 76 95 db -40 c < t < 125 c 72 cmr2 common mode rejection ratio cmr = 20 log ( v ic / v io ) (v ic = -0.1 v to v cc + 0.1 v, v out = v cc /2, r l > 1 m ) t = 25 c 60 78 -40 c < t < 125 c 56 svr common mode rejection ratio 20 log ( v cc / v io ) (v cc = 3 v to 16 v, v out = v icm = v cc /2) t = 25 c 76 90 -40 c < t < 125 c 72 a vd large signal voltage gain (v out = 0.5 v to (v cc - 0.5 v), r l > 1 m ) t = 25 c 85 -40 c < t < 125 c 83 v oh high level output voltage (v oh = v cc - v out ) r l = 10 k , t = 25 c r l = 10 k , -40 c < t < 125 c 70 100 mv v ol low level output voltage r l = 10 k , t = 25 c r l = 10 k , -40 c < t < 125 c 70 100 i out i sink v out = v cc , t = 25 c 40 92 ma v out = v cc , -40 c < t < 125 c 35 i source v out = 0 v, t = 25 c 30 90 v out = 0 v, -40 c < t < 125 c 25 i cc supply current (per channel, v out = v cc /2, r l > 1 m ) t = 25 c 250 360 a -40 c < t < 125 c 400 v month ---------------------------
electrical characteristics tsx56x, tsx56xa 10/27 docid023274 rev 3 ac performance gbp gain bandwidth product r l = 10 k , c l = 100 pf 750 900 khz f u unity gain frequency 750 m phase margin 55 degree g m gain margin 9 db sr slew rate r l = 10 k , c l = 100 pf, v out = 0.5 v to v cc - 0.5 v 1.1 v/ s e n low-frequency peak-to-peak input noise bandwidth: f = 0.1 to 10 hz 15 v pp e n equivalent input noise voltage density f = 1 khz f = 10 khz 48 27 thd+n total harmonic distortion + noise follower configuration, f in = 1 khz, r l = 100 k , v icm = (v cc - 1.5 v)/2, bw = 22 khz, v out = 5 v pp 0.0005 % 1. see section 4.3: input offset voltage drift over temperature on page 15 . 2. typical value is based on the v io drift observed after 1000h at 125 c extrapo lated to 25 c using the arrhenius law and assuming an activation energy of 0.7 ev. the operational amplifier is aged in follower mode configuration. 3. guaranteed by design. table 6. electrical characteristics at v cc+ = +16 v with v cc- = 0 v, v icm = v cc /2, t amb = 25 c, and r l = 10 k connected to v cc /2 (unless otherwise specified) (continued) symbol parameter conditions min. typ. max. unit nv hz ----------- -
docid023274 rev 3 11/27 tsx56x, tsx56xa electrical characteristics figure 6. input offset voltage vs. temperature at v cc = 16 v figure 2. supply current vs. supply voltage at v icm = v cc /2 figure 3. input offset voltage distribution at v cc = 16 v and v icm = 8 v figure 4. input offset voltage temperature coefficient distribution at v cc = 16 v, v icm = 8 v figure 5. input offset voltage vs. input common mode voltage at v cc = 12 v /lplwiru76;[ 9 && 99 lfp 9 /lplwiru76;[$ $0
electrical characteristics tsx56x, tsx56xa 12/27 docid023274 rev 3 figure 7. output current vs. output voltage at v cc = 3.3 v figure 8. output current vs. output voltage at v cc = 5 v figure 9. output current vs. output voltage at v cc = 16 v figure 10. bode diagram at v cc = 3.3 v figure 11. bode diagram at v cc = 5 v figure 12. bode diagram at v cc = 16 v
docid023274 rev 3 13/27 tsx56x, tsx56xa electrical characteristics figure 13. phase margin vs. capacitive load at v cc = 12 v figure 14. gbp vs. input common mode voltage at v cc = 12 v figure 15. a vd vs. input common mode voltage at v cc = 12 v figure 16. slew rate vs. supply voltage figure 17. noise vs. frequency at v cc = 3.3 v figure 18. noise vs. frequency at v cc = 5 v
electrical characteristics tsx56x, tsx56xa 14/27 docid023274 rev 3 figure 19. noise vs. frequency at v cc = 16 v figure 20. distortion + noise vs. output voltage amplitude figure 21. distortion + noise vs. amplitude at v icm = v cc /2 and v cc = 12 v figure 22. distortion + noise vs. frequency
docid023274 rev 3 15/27 tsx56x, tsx56xa application information 4 application information 4.1 operating voltages the amplifiers of the tsx56x and tsx56xa series can operate from 3 v to 16 v. their parameters are fully specified at 3.3 v, 5 v and 16 v power supplies. however, the parameters are very stable in the full v cc range. additionally, the main specifications are guaranteed in extended temperature ranges from -40 to +125 c. 4.2 rail-to-rail input the tsx56x and tsx56xa devices are built with two complementary pmos and nmos input differential pairs. the devices have a rail-to-rail input, and the input common mode range is extended from v cc- - 0.1 v to v cc+ + 0.1 v. however, the performance of these devices is clearly optimized for the pmos differential pairs (which means from v cc- - 0.1 v to v cc+ - 1.5 v). beyond v cc+ - 1.5 v, the operational amplifiers are still functional but with degraded performance, as can be observed in the electr ical characteristics section of this datasheet (mainly v io and gbp). these performances are su itable for a number of applications needing to be rail-to-rail. the devices are designed to prevent phase reversal. 4.3 input offset voltage drift over temperature the maximum input voltage drift over the temperature variation is defined as the offset variation related to the offset value measured at 25 c. the operational amplifier is one of the main circuits of the signal conditioning chain, and the amplifier input offset is a major contributor to the chain accuracy. the signal chain accuracy at 25 c can be compensated during production at application level. the ma ximum input voltage drift over temperature enables the system designer to anticipate the effects of temperature variations. the maximum input voltage drift over temperature is computed in equation 1 . equation 1 with t = -40 c and 125 c. the datasheet maximum value is guaranteed by measurement on a representative sample size ensuring a c pk (process capability in dex) greater than 2. v io t ----------- - max v io t () v io 25 c () ? t25 c ? --------------------------------------------------- =
application information tsx56x, tsx56xa 16/27 docid023274 rev 3 4.4 long term input offset voltage drift to evaluate product reliability, two ty pes of stress acceleration are used: ? voltage acceleration, by changing the applied voltage ? temperature acceleration, by changing the die temperature (below the maximum junction temperature allowed by the technology) with the ambient temperature. the voltage acceleration has been defined bas ed on jedec results, and is defined using equation 2 . equation 2 where: a fv is the voltage acceleration factor is the voltage acceleration constant in 1/v, constant technology parameter ( = 1) v s is the stress voltage used for the accelerated test v u is the voltage used for the application the temperature acceleration is driven by the arrhenius model, and is defined in equation 3 . equation 3 where: a ft is the temperature acceleration factor e a is the activation energy of the technology based on the failure rate k is the boltzmann constant (8.6173 x 10 -5 ev.k -1 ) t u is the temperature of the die when v u is used (k) t s is the temperature of the die under temperature stress (k) the final acceleration factor, a f , is the multiplication of the voltage acceleration factor and the temperature acceleration factor ( equation 4 ). equation 4 a f is calculated using the temperature and volt age defined in the mission profile of the product. the a f value can then be used in equation 5 to calculate the number of months of use equivalent to 1000 hours of reliable stress duration. a fv e v s v u ? () ? = a ft e e a k ------ 1 t u ------ 1 t s ------ ? ?? ?? ? = a f a ft a fv =
docid023274 rev 3 17/27 tsx56x, tsx56xa application information equation 5 to evaluate the op-amp reliability, a fo llower stress conditio n is used where v cc is defined as a function of the maximum operating voltage and the absolute maximum rating (as recommended by jedec rules). the v io drift (in v) of the product after 1000 h of stress is tracked with parameters at different measurement conditions (see equation 6 ). equation 6 the long term drift parameter ( v io ), estimating the reli ability performance of the product, is obtained using the ratio of the v io (input offset voltage value) dr ift over the square root of the calculated number of months ( equation 7 ). equation 7 where v io drift is the measured drift value in the specified test conditions after 1000 h stress duration. 4.5 pcb layouts for correct operation, it is advised to add 10 nf decoupling capacitors as close as possible to the power supply pins. 4.6 macromodel accurate macromodels of the tsx56x, tsx56xa devices are available on the stmicroelectronics? website at www.st.com . these models are a trade-off between accuracy and complexity (that is, time simulation) of the tsx56x and tsx56xa operational amplifiers. they emulate the nominal performanc e of a typical device within the specified operating conditions mentioned in the datash eet. they also help to validate a design approach and to select the right operational amplifier, but they do not replace on-board measurements . months a f 1000 h 12 months 24 h 365.25 days () ? = v cc maxv op with v icm v cc 2 ? == v io v io drift months () ------------------------------ =
package information tsx56x, tsx56xa 18/27 docid023274 rev 3 5 package information in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack specifications, grade definitions a nd product status are available at: www.st.com . ecopack is an st trademark.
docid023274 rev 3 19/27 tsx56x, tsx56xa package information 5.1 sot23-5 package information figure 23. sot23-5 package mechanical drawing table 7. sot23-5 package mechanical data ref. dimensions millimeters inches min. typ. max. min. typ. max. a 0.90 1.20 1.45 0.035 0.047 0.057 a1 0.15 0.006 a2 0.90 1.05 1.30 0.035 0.041 0.051 b 0.35 0.40 0.50 0.013 0.015 0.019 c 0.09 0.15 0.20 0.003 0.006 0.008 d 2.80 2.90 3.00 0.110 0.114 0.118 d1 1.90 0.075 e 0.95 0.037 e 2.60 2.80 3.00 0.102 0.110 0.118 f 1.50 1.60 1.75 0.059 0.063 0.069 l 0.10 0.35 0.60 0.004 0.013 0.023 k0 10 0 10
package information tsx56x, tsx56xa 20/27 docid023274 rev 3 5.2 dfn8 2x2 pack age information figure 24. dfn8 2x2 package mechanical drawing table 8. dfn8 2x2 package mechanical data ref. dimensions millimeters inches min. typ. max. min. typ. max. a 0.70 0.75 0.80 0.028 0.030 0.031 a1 0.00 0.02 0.05 0.000 0.001 0.002 b 0.15 0.20 0.25 0.006 0.008 0.010 d 2.00 0.079 e 2.00 0.079 e 0.50 0.020 l 0.045 0.55 0.65 0.018 0.022 0.026 n8 8 h / %277209,(: 3lq,' 3,1,1'(;$5($ ( & $ $ 3/$1( 6($7,1* 7239,(: & & [ [ ' 3,1,1'(;$5($ esofv & & $ % % $ & 6,'(9,(: *$06&%
docid023274 rev 3 21/27 tsx56x, tsx56xa package information 5.3 miniso8 package information figure 25. miniso8 package mechanical drawing table 9. miniso8 package mechanical data symbol dimensions millimeters inches min. typ. max. min. typ. max. a 1.10 0.043 a1 0 0.15 0 0.006 a2 0.75 0.85 0.95 0.030 0.033 0.037 b 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 d 2.80 3.00 3.20 0.11 0.118 0.126 e 4.65 4.90 5.15 0. 183 0.193 0.203 e1 2.80 3.00 3.10 0.11 0.118 0.122 e 0.65 0.026 l 0.40 0.60 0.80 0. 016 0.024 0.031 l1 0.95 0.037 l2 0.25 0.010 k 0 8 0 8 ccc 0.10 0.004
package information tsx56x, tsx56xa 22/27 docid023274 rev 3 5.4 qfn16 3x3 package information figure 26. qfn16 3x3 package mechanical drawing h %277209,(: 3lq,' ( & $ $ 3/$1( 6($7,1* & & [ [ ' e & & $ % % $ & 6,'(9,(: *$06&% ,1'(;$5($ '[( ddd ddd 7239,(: fff hhh / eee eee & 5
docid023274 rev 3 23/27 tsx56x, tsx56xa package information table 10. qfn16 3x3 package mechanical data ref. dimensions millimeters inches min. typ. max. min. typ. max. a 0.50 0.65 0.020 0.026 a1 0 0.05 0 0.002 b 0.18 0.25 0.30 0.007 0.010 0.012 d3.00 0.118 e3.00 0.118 e 0.50 0.020 l 0.30 0.50 0.012 0.020 aaa 0.15 0.006 bbb 0.10 0.004 ccc 0.10 0.004 ddd 0.05 0.002 eee 0.08 0.003
package information tsx56x, tsx56xa 24/27 docid023274 rev 3 5.5 tssop14 package information figure 27. tssop14 package mechanical drawing table 11. tssop14 package mechanical data symbol dimensions millimeters inches min. typ. max. min. typ. max. a 1.20 0.047 a1 0.05 0.15 0.002 0.004 0.006 a2 0.80 1.00 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 d 4.90 5.00 5.10 0.193 0.197 0.201 e 6.20 6.40 6.60 0.244 0.252 0.260 e1 4.30 4.40 4.50 0.169 0.173 0.176 e 0.65 0.0256 bsc l 0.45 0.60 0.75 l1 1.00 k 0 8 0 8 aaa 0.10 0.018 0.024 0.030
docid023274 rev 3 25/27 tsx56x, tsx56xa ordering information 6 ordering information table 12. order codes order code temperature range channel number package packaging marking tsx561ilt -40 to 125 c 1sot23-5 tape and reel k23 tsx562iq2t 2 dfn8 2 x 2 tsx562ist 2 miniso8 tsx564iq4t 4 qfn16 3 x 3 tsx564ipt 4 tssop14 tsx564i tsx561iylt -40 to 125 c automotive grade (1) 1sot23-5 k116 tsx562iyst 2 miniso8 tsx564iypt 4 tssop14 tsx564iy TSX561AILT -40 to 125 c 1sot23-5 k117 tsx562aist 2 miniso8 tsx564aipt 4 tssop14 tsx564ai tsx561aiylt -40 to 125 c automotive grade (1) 1sot23-5 k118 tsx562aiyst 2 miniso8 tsx564aiypt 4 tssop14 tsx564aiy 1. qualification and characterization acco rding to aec q100 and q003 or equivalen t, advanced screening according to aec q001 and q 002 or equivalent are ongoing.
revision history tsx56x, tsx56xa 26/27 docid023274 rev 3 7 revision history table 13. document revision history date revision changes 06-jun-2012 1 initial release. 18-sep-2012 2 added tsx562, tsx564, tsx562a, and tsx564a devices. updated features , description , figure 1 , table 1 (added dfn8, miniso8, qfn16, and tssop14 package). updated table 1 (updated esd mm values). updated table 4 and table 5 (added footnotes), section 5 (added figure 24 to figure 27 and table 8 to table 11 ), table 12 (added dual and quad devices). minor corrections throughout document. 23-may-2013 3 replaced the silhouette, pinout, package diagram, and mechanical data of the dfn8 2x2 and qfn16 3x3 packages. added benefits and related products . table 1 : updated r thja values and added r thjc values for dfn8 2x2 and qfn16 3x3. updated section 4.3 , section 4.4 , and section 4.6 replaced figure 23: sot23-5 package mechanical drawing and table 7: sot23-5 package mechanical data .
docid023274 rev 3 27/27 tsx56x, tsx56xa please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not authorized for use in weapons. nor are st products designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of TSX561AILT

	To Download TSX561AILT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .